Showing posts with label Video. Show all posts
Showing posts with label Video. Show all posts

Thursday, 16 March 2017

Simple Project to Build A Video Signal Emphasis


With this circuit we can amplification selectively the high signal of picture frequencies [Video] with result bigger clarity than this. The circuit should be placed between a Video unit and the reception Scart or the plug Video input of television receiver. The designing is simple, it’s based in three only transistor.

Video Signal Emphasis Circuit Diagram

Video Signal Emphasis Circuit Daigram

The first stage of Q1 function as isolator - adapter of input impedance. The second stage round the Q2 in common base connection which the gain is determined by the TR2. The TR1, R6 and C3 determine the frequency response. The third stage round the Q3 works as output buffer and 75-ohm line driver. The TR2 should be regulated in a place where the circuit output voltage, to be 1Vp-p, in 75 ohm load. The circuit functions with 12Volts - 50mA well stabilized.

Part List

R1=82ohm
R2=5.6Kohm
R3-9-11=2.7Kohm
R4=330ohm
R5=220ohm
R6=470ohm
R7=270ohm
R8=12Kohm
 R10=2.2Kohm
R12=180ohm
R13=68ohm
C1-4-5=100uF 16V
C2=2200uF 16V
C3=470pF ceramic
C6=470uF 16V
C7=220uF 16V
C8=100nF 100V MKT
TR1=250ohm trimmer
TR2=500ohm trimmer
D1=1N4148
Q1-2-3=BC547
J1-2=Female RCA jack
J3=2pin connector 2.54mm step

Video Signal Emphasis PCB 


Video Signal Emphasis PCB



Readmore → Simple Project to Build A Video Signal Emphasis

Wednesday, 8 March 2017

Simple Cell Phone Controlled Audio Video Mute Switch


This is a project of simple circuit of the cell phone-controlled audio/video mute switch. This cell-phone-controlled audio/ video mute switch is highly useful in automobiles. The circuit automatically disconnects power supply to the audio/video system whenever the mobile handset is lifted off the holder for making or receiving a call. You can use any readily available cell-phone holder with some mi-nor alterations or fabricate it yourself as shown in Fig. 1.  
Proposed cell-phone holder Fig. 1: Proposed cell-phone holder
 
The circuit is wired around IC LM555 (IC1), the CMOS version of timer NE555, as shown in Fig. 2. IC1 is used as a medium current line driver with either an inverting or non-inverting output. It can sink (or source) current of up to 50 mA only, so take care while handling it. The audio/video system is connected to the circuit via normally opened (N/O) contacts of the relay.
 
circuit of the cell phone-controlled audio video mute switch Fig. 2: The circuit of the cell phone-controlled audio/video mute switch
 
When the cell phone is in its holder, LDR1 does not receive any light from white LED1 and its resistance is high. As a result, the voltage at pin 2 of IC1 re-mains high to provide a low output at pin 3. The low output of IC1 activates relay RL1 and the audio/video system gets power supply via its N/O contacts. LED3 glows to indicate that the audio/video system is ‘on.’  When the handset is taken off the holder, light rays from LED1 fall on LDR1 and its resistance decreases. As a result, the voltage at pin 2 of IC1 de-creases to provide a high output at its pin 3. The high output of IC1 deactivates relay RL1 and the audio/video system does not get power supply. LED2 glows to indicate that the audio/video system is ‘off.’   Preset VR1 is used to control the sensitivity of the circuit. Zener diode ZD1 is used for protecting white LED1 from the higher voltage. The circuit works off a 12V car battery. Switch S1 can be used to manually switch on/off the audio/video system.
 

Author : T.K. Hareendran - Copyright:  Electronics For You

Readmore → Simple Cell Phone Controlled Audio Video Mute Switch

Thursday, 12 January 2017

Video Switch for Intercom System


Nowadays a lot of intercom units are  equipped with video cameras so that you can  see as well as hear who is at the door. Unfortunately, the camera lens is perfectly placed  to serve as a sort of support point for people  during the conversation, with the result that  there’s hardly anything left see in the video  imagery.  One way to solve this problem is to install two cameras on the street side instead only  one, preferably some distance apart. If you  display the imagery from the two cameras  alternately, then at least half of the time you  will be able to see what is happening in front  of the door. Thanks to the video switch module described  here, which should be installed on the street  side not too far away from the two cameras,  you need only one monitor inside the house and you don’t need to install any additional video cables.

 

Circuit diagram :

Video Switch for Intercom System-Circuit-Diagram

Video Switch for Intercom System Circuit Diagram

 

Along with a video switch, the circuit includes  a video amplifier that has been used with  good results in many other Elektor projects,  which allows the brightness and the contrast  to be adjusted separately. This amplifier is  included because the distance between the  street and the house may be rather large, so it is helpful to be able to compensate for cable attenuation in this manner.  The switch stage is built around the well  known 4060 IC, in which switches IC2a and  IC2d alternately pass one of the two signals to  the output. They are driven by switches IC2b and IC2c, which generate control signals that  are 180 degrees out of phase. The switching rate for the video signals is  determined by a clock signal from an ‘old  standby’ 555 IC, which causes the signals to  swap every 2 seconds with the specified com ponent values.

 

Naturally, this circuit can also used in many other situations, such as where two cameras are needed for surveillance but only one video cable is available.

 

Author :Jacob Gestman Geradts - Copyright : Elektor

Readmore → Video Switch for Intercom System

Tuesday, 10 January 2017

The Audio Video Distribution Amplifier


With the amount of equipment in home entertainment centers today the need to be able to vary the gain of the audio or video signal is needed. I found this particular circuit helpful when used in conjunction with the Universal Descrambler and a Stabilizer circuit I built for making copies of video tapes. It not only allowed me the ability to fine tune the video strength it also helped me increase the recorded audio which typically becomes poor when making tape copies. Circuit operation is straight forward for amplifier circuits. The second channel for the audio amplifier is made up of the same components except the other half of IC1 is used. Pin 6 & 5 are inputs and 7 is the output.

Circuit Diagram
The Audio/Video Distribution Amplifier

Readmore → The Audio Video Distribution Amplifier

Thursday, 5 January 2017

Camera Video Amplifier Circuit Transistorized


There are occasions  when you want to view your video clips taken in your digital camera on  your TV.You can do so by interfacing the camera video output to video input of your TV.But this times you cant connect directly as it needs some amplification before the signal reaches from camera to television


The video amplifier schematic circuit shown in the figure is a simple PAL video amp, expected to have a 3db bandwidth of 5.5MHz. You can connect your camera to TV through this circuit. So this is a low level transistorized video amplifier stage that accepts 1V (p-p) and outputs 2V(p-p) signal. 

Notes The circuit requires a 5V dc power supply



Readmore → Camera Video Amplifier Circuit Transistorized