Secret Diagram

This is an economic circuit of a mini solar lighting system, solar panel 6V/2W is used to charge a rechargeable 4V/800mAh through a current limiting circuit load that uses a LM317T adjustable regulator 3 pin (IC1). Assuming a sunny day 6 hours, a panel will enviarr 2 watts for approximately 900mAh battery. The current can be reduced by increasing the value of R1, for example, 8.2 to 10 ohms ohms.

 Lighting Garden with Solar Energy Circuit Diagram

6V/2W:Maximum power (Pm): 

2WWorking Voltage (Vmp): 

9VWorking Current (Imp): 

220mAOpen Circuit Voltage (Voc): 

10.5VPower Tolerance: -3% to 5%

Presented here is a simple circuit that uses six red, green and blue (RGB) LEDs to generate a running-light effect in seven colours—blue, green, red, cyan, yellow, magenta and white. The RGB LEDs have four pins, one for each colour and a common cathode. Different colours can be produced by mixing the primary colours (i.e., red, green and blue).


Circuit and working
The circuit diagram for the seven-colour LED lighting is shown in Fig. 2. The circuit is built around timer NE555 (IC1), decade counter CD4017B (IC2), four-bit binary counter 7493 (IC3), driver IC ULN2003 (IC4), six RGB LEDs (RGB1 through RGB6), three BC547 transistors (T1 through T3) along with some basic components.

The timer IC NE555 (IC1) is wired in astable multivibrator mode. It provides low-frequency clock pulses, the frequency of which is decided by timing components R1, VR1 and C2. The frequency of the timer can be varied using the preset VR1.

The output of IC1 at pin 3 is fed to decade counter CD4017B (IC2). IC2 has ten outputs, which go high in sequence when a source of pulses is connected to its CLK input (pin 14). Q0 through Q5 of IC2 are connected to IN1 through IN6 of IC4. Pin Q6 of IC2 is connected back to its reset pin 15 and input pin 1 of IC3 via diode D1. When Q6 pin of IC2 goes high, it resets IC2 and, at the same time, provides the high input clock to IC3 each time after the sixth clock of IC1.



IC3 is a four-bit binary counter, and its outputs QB through QD are connected to the bases of transistors T1 through T3 via resistors R21 through R23, respectively. The binary outputs of IC3 make corresponding transistors conduct and select a different colour after each cycle (see Table I).

The common-cathode pins of each RGB LED are connected to the outputs of IC4 as shown in Fig. 2. ULN2003 is used for driving these LEDs. You can add even more RGB LEDs in parallel to the existing ones to make a larger lighting system.

The working of the circuit is simple. When the circuit is switched on, the clock pulse is generated from pin 3 of the timer IC1, making outputs of IC2 high, sequentially, which decides the switching rate of LEDs that can be changed through VR1. The colours are selected by the binary output of IC3, which changes after every sixth pulse from IC1.






Construction and testing
A single-side PCB for seven-colour LED lighting is shown in actual size in Fig. 3, and its component layout is shown in Fig. 4. After assembling the circuit on a PCB, enclose it in a suitable case. You can wire LEDs the way you like and connect on the PCB. The circuit uses a 5V DC supply.



To test if the circuit is functioning properly, check the input supply at TP1 with respect to TP0. The output pulses generated by IC1 can be checked at TP2 with the help of an oscilloscope. The frequency of these clock pulses can be varied by VR1. The clock pulse to the binary counter IC3 can be checked at TP3.